MOS / Rockwell / WDC · Microcontroller

MOS 6502

The 8-bit CPU behind the Apple II, C64, NES and BBC Micro, and still the usual first homebrew computer build.

Cheat sheet (SVG)

Logic level: 5 V
Package: PDIP-40

1.Pinout diagram

Highlight a signalhover to preview, click to keep

Pins 1-20

6502

Pins 21-40

Pin detail

Hover a pin for its mappings and gotchas. Click to keep it here.

Logic level: 5 V
Package: PDIP-40

Fig. 1. MOS 6502, PDIP-40. Hover or tap a signal to light up every pin that carries it.

2.Caution

The address bus is output only and the data bus is bidirectional, steered by R/W. There is no bus request or acknowledge: on an NMOS 6502 nothing else can drive the bus, which is why DMA designs gate the clock instead.
Feed the clock into pin 37, phase 0 in. Pins 3 and 39 are the buffered phase 1 and phase 2 outputs; phase 2 is what peripherals and address decoding should be qualified with.
Reset needs to stay low for at least two clock cycles after the supply is stable. The CPU then reads the vector at FFFC and FFFD.
Vectors live at the top of memory: NMI at FFFA, RESET at FFFC, IRQ and BRK at FFFE.
IRQ is level sensitive and maskable with SEI. NMI is edge triggered and cannot be masked, so a noisy NMI line gives you interrupts you never asked for. Tie both high through a resistor if unused.
The NMOS 6502 has no minimum clock speed restriction going up but will lose state if clocked too slowly. The CMOS W65C02 is fully static, so you can single-step it by hand with a debounced switch. That alone makes it the better part to learn on.
On the W65C02 the unused pins change: pin 5 becomes ML, pin 36 becomes BE, and pin 38 becomes SOB. Pin 1 also becomes VPB on some variants.

3.Minimum circuit to run

What has to go around the chip before it will run.

Fig. 2. Minimum circuit to run, drawn from Table 1. Crossing wires are not connected.

Table 1. External parts, and why each one is there.
Part	Between	Why
Clock oscillator	PHI0 (37) to GND	A can oscillator or a crystal and gate. The NMOS part also has a minimum clock speed.
10 kOhm	RES (40) to VCC	Reset pull-up, with a capacitor to ground for a power-on reset of at least two cycles.
10 kOhm	IRQ (4) to VCC	Unused interrupt inputs must be held high or you get interrupts you never asked for.
10 kOhm	NMI (6) to VCC	NMI is edge triggered and cannot be masked, so a floating pin is worse than IRQ.
10 kOhm	RDY (2) to VCC	RDY is an active input and must be tied off.
10 kOhm	SO (38) to VCC	Set-overflow is an active input and must be tied off.
100 nF	VCC (8) to GND	Supply decoupling at the pin.

Qualify address decoding with PHI2 (39), not with the raw address lines, or peripherals will see bus noise as accesses.

4.Full pin reference

Every pin, alias and mapping. This is the table that prints.

Table 2. Pin assignments.

Complete pin reference for MOS 6502
Pin	Name	Also called	Functions	Notes
1	VSS	-	Ground
2	RDY	-	Ready	Pull low to freeze the CPU on a read cycle, for slow memory. Tie high if unused.
3	PHI1OClock	O1 OUT, phase 1 out	Phase 1 clock out
4	IRQ	IRQB	Maskable interrupt, active low	Level sensitive. Tie high through 3k3 if unused.
5	NC	-	Not connected	ML (memory lock) on the W65C02.
6	NMI	NMIB	Non-maskable interrupt, active low	Edge triggered and unmaskable. Tie high through 3k3 if unused.
7	SYNC	-	Opcode fetch indicator	High during the first cycle of every instruction. The hook for single-stepping and for a hardware debugger.
8	VCC5 V	-	Positive supply
9	A0	-	Address bus bit 0
10	A1	-	Address bus bit 1
11	A2	-	Address bus bit 2
12	A3	-	Address bus bit 3
13	A4	-	Address bus bit 4
14	A5	-	Address bus bit 5
15	A6	-	Address bus bit 6
16	A7	-	Address bus bit 7
17	A8	-	Address bus bit 8
18	A9	-	Address bus bit 9
19	A10	-	Address bus bit 10
20	A11	-	Address bus bit 11
21	VSS	-	Ground
22	A12	-	Address bus bit 12
23	A13	-	Address bus bit 13
24	A14	-	Address bus bit 14
25	A15	-	Address bus bit 15
26	D7	-	Data bus bit 7
27	D6	-	Data bus bit 6
28	D5	-	Data bus bit 5
29	D4	-	Data bus bit 4
30	D3	-	Data bus bit 3
31	D2	-	Data bus bit 2
32	D1	-	Data bus bit 1
33	D0	-	Data bus bit 0	The data bus runs D7 down to D0 as the pin numbers go up.
34	RW	R/W	Read high, write low
35	NC	-	Not connected
36	NC	-	Not connected	BE (bus enable) on the W65C02.
37	PHI0Clock	O0 IN, phase 0 in, CLK	Clock in	This is the pin your oscillator drives.
38	SO	S.O.	Set overflow flag	A falling edge sets V in the status register. Tie high if unused.
39	PHI2OClock	O2 OUT, phase 2 out	Phase 2 clock out	Qualify address decoding and peripheral chip selects with this.
40	RES	RESB, RESET	Reset, active low	Hold low for at least two cycles after the supply settles.

Looking for a substitute?

MOS 6502, 7 alternatives

Primary sources

Found a wrong pin? The whole board is one file, data/boards/mos-6502.json.

Edit this file on GitHub Report it instead